Rocking creative engraving
I like to engrave but I don’t have to law, my small friends who have a minute is paying attention! If you feel that the barrack threshold is too high, you can start from a simpler and lively rubber chapter, easy to get started.
The rubber chapter, as the name refers to the seal of rubber, using a small engraving knife in a rubber brick dedicated to the engraving or a handmade work, can be used repeatedly. The rubber chapter is also a kind of print art, and the rubber is just a material applied, just like the prints we are well known to the wooden board, copper plate, slate, etc.
Playing art has developed with the inventions of printing. This kind of rustic art has a pivotal position in the printing industry. Today, simple and easy-to-operate rubber chapter is quietly raised. More and more people fall in love with the happiness in the eraser production process, enjoy this knife, a fine carving, feel this “painting” and “engraving”, ” Top “and” Print “,” Concave “and” Convex “,” Yin “and” Yin “.
If you also want to feel this coming from the original rustic manual printing, let’s move together ~
Tools and materials
Cutting pad |
Protect the desktop and blade when cutting.
Sulfuric acid paper |
Also known as the drawing paper, the transparency is not easy to break.
Carving rubber brick |
Special rubber bricks produced for handmade rubber chains, there are various sizes and colors, it is recommended that beginners choose the “sandwich” color rubber brick.
Car engraving, mare knife, pencil |
The knife is the main tool, also known as a pen knife, it is recommended to use a 30 ° engraving knife and a perfect knife.
Corner and round knife |
In order to use the tool, the corner knife is “V” shape, suitable for engraving thin lines, the round knife knife is “U” shape, mostly used to dig out the leaves.
Pieces, plastic eraser |
Diabed can also be replaced by magnetic card or coins. Plastic plastic rubber is used to remove pencil charcoal powder on the rubber chapter.
7. Scaling of the mud | It is divided into oily and water resistance, which can be used in paper, and there is also a special printing on smooth material such as cloth, ceramic, wood.
Engraving rubber chapter
1. Punch a simple pattern or use the ready-made pattern directly. The sulfuric acid paper was covered on the pattern, and the pattern under the sulfuric acid paper was drawn with a pencil.
2. Select a rubber brick to flip over the sulfuric acid paper with a pattern over, cover down the rubber brick, prepare the transfer of the pattern. In order to prevent shifts, it is also possible to temporarily fix the sulfuric acid paper on a rubber brick with a tape.
3. One hand is fixed to the sulfuric acid paper, and the other hand is applied in a place where there is a pattern.
4. After the scraping, the hand of the drawing paper is safe, and the paper is revealed to see if there is a leaking line and the transfer is not clear enough. If you put the drawings and scrape it. You can also use the pencil to make it directly on the rubber brick.
5. After the transfer is completed, cut it from the rubber brick with the USge knife.
6. Pick up the engrave knife with a pen, the blade looks forward.
7. Insert the pattern line perpendicular to yourself, and the pen knife is tilted about 45 degrees into the rubber.
8. Close the winding of the outer ring of the feathers, slowly drive the knife tip to advance, the blade is always forward, rotating the rubber brick without rotating the knife.
9. After the contour of the whole circle, a loop is in turn around the right side from the right side of the pattern line.
10. Parallel with the first incision and the pen knife remains about 45 degrees.
11. After the completion of the two incisions, you can dig out a “V” shape, can’t get or break because the opposite knife is not sprayed, and you can make a knife again.
12. The hollow part of the feather is the same, the method is the same, pay attention to the outer ring of the pattern portion is outward.
13. This is a two-knife. You can dig off the part you want to remove.
14. Gently engrave the lines in the previous way in the past.
15. Remove the edge portion with the USD knife.
16. Then remove the outer ring of the rubber chapter. Between the black and white two floors with the USge knife, the blade always keeps parallel with the surface of the chapter, while turning the chapter while paying attention to the cutting part, the control is slow, so as not to cut the hand.
17. Strip the edges of the edge.
18. Use the plastic rubber to scroll or press the surface of the chapter, remove pencil carbon powder.
19. In order to punch it on the chapter.
20. Put the rubber chapter on the table and gently patched the surface with the print.
21. One hand pressing paper, and the other hand is vertically lifted, and the print is complete!
22. Tangle carving technique: insert the blanket in the pen knife 45 degrees.
23. The knife does not move, turn a circle to the rubber chapter to complete a hole.
24. We will print freely.
Saving of the rubber chapter
The rubber chapter should be closed in a cool dry place because the rubber chapter is superimposed to be easily adhesive, so it is best to store it independently or layered, and store it with a transparent small bag or its own carton.